Dear Krunal chauhan, In the current Yocto version(PD19.1.0) Podman package will not support. So you need to upgrade your Yocto version to BSP-Yocto-i.MX6UL-PD21.1.0. This version PD21.1.0 will support both podman and docker. Path for the Podman package: https://layers.openembedded.org/layerindex/recipe/107131/ And select the branch [dunfell (Yocto Project 3.1)].

Hi Shivam Rawat, Kindly follow the attached file for the compilation of YOCTO in your host pc and if you face any error again let us know.

Hi Shivam Rawat, Kindly follow the attached file for the compilation of YOCTO in your host pc and ubuntu 16.04 is preferable.

Hi Abhinet Pandey, Kindly try with 8gb or 16gb SD card for making the partition. For preparing the Bootable SD card follow the below link https://developer.ruggedboard.com/g5-system-development-guide/boot-from-sd-card

Hi Abhinet Pandey, Kindly follow the below steps. Step 1: After booting the board from MMC set the date in board by following the commands #date 071910102022.55 (date mmddhhmmyyyy.ss) #hwclock -w -f /dev/rtc0 #hwclock -r -f /dev/rtc0 Step 2: Check the internet connection in the board by connecting the Ethernet cable from the RB-A5D2x board to pc by following the below commands #ping google.com Step 3: Install pymodbus by following the below commands $ pip3 install pymodbus Please check the hardware connections of Energy meter with RB-A5D2x board properly.

Dear Pritesh Jani, Kindly follow the Schematic of RB ADC/RTD attached.

Hi Anna Varghese, Please share the log of the error you are facing and I think you may made the connection wrong. First test the CAN communication between two RB-A5D2x boards.

Dear Santhosh Kumar, Yes we can add external EEPROM to the board through I2c bus. We can make the i2c communication through mikrobus connector in RB-A5D2x.

Dear Abhinet pandey, Please Boot the board from NOR/MMC And connect the First pin of the P5 connector to the input voltage and Fifth pin of the P5 connector to the Ground and follow the below commands. $ echo 84 > /sys/class/gpio/export $ echo in > /sys/class/gpio/PC20/direction $ cat /sys/class/gpio/PC20/value Remove the patch card and give the below command $ cat /sys/class/gpio/PC20/value The value of digital pin is changed one to zero.

Hi Lukalapu Santhosh Rao, Kindly follow the schematics of RB-A5D2x attached.

Thank you for sharing your input about the update of At91Bootstrap on our community forum 😊

Thank you for sharing your input about the update of At91Bootstrap on our community forum 😊

Dear Lukalapu Santhosh Rao, Kindly follow the pin mux excel sheet attached.

Hi Shivam rawat, The Display controller used in PhyCore - i.MX6 UL (MCIMX6G2CVM05AB) is eLCDIF and the Display Interface currently using is RGB and the display interface part no. is KD070C-4-C004A.

Hi Shivam rawat, You can customize your toochain through yocto. Complete your yocto setup for RB-i.MX 6UL according to your requirement and then generate an sdk.

Hi Shivam rawat, Do you have Yocto setup for RB-i.MX 6UL. If not please follow the below guide for Yocto setup in your host pc. Once you complete the Yocto setup leave us a command.

Thank you for sharing your input about the update of u-boot on sama5d2 on our community forum 😊

Dear Gunjan, Kindly follow the Yocto Guide attached to build and customise linux build for i.MX 6UL board. Thank you, PHYTEC India support